PROMAG50 Electromagnetic Flowmeter Quick Setup Operation Guide

PROMAG50 Electromagnetic Flowmeter Quick Setup Operation Guide

The PROMAG50 electromagnetic flowmeter is a high-precision instrument commonly used in industrial flow measurement. This article provides detailed steps for its quick setup operation, helping engineering technicians and procurement personnel efficiently complete commissioning. Correct settings ensure measurement accuracy and output signal stability.

Key Definitions

• "+" key: Menu up, data increment;
• "-" key: Menu down, data decrement;
• "E" key: Enter submenu, confirm operation, and save data;
• "+/-" key: Press "+" and "-" simultaneously to return to the previous menu.

Basic Operation Steps

1. Open the meter cover and press the "E" key to enter the setup menu;
2. Press the "+" key twice until "GROUP SELECT" appears, press the "E" key to enter, and "SETUP COMMISSION QUICK SETUP NO" appears;
3. Use the "+" key, "-" key, and "E" key to enter the password "0050" digit by digit, then press the "E" key to confirm;
4. Use the "+" key and "-" key to select the corresponding parameter item, press the "E" key to enter the parameter item, use the "+" key and "-" key to set the parameters, and press the "E" key to confirm after setting (refer to the quick setup menu in the manual for specific menus);
5. After parameter setting is complete, press the "+/-" key and hold for 3 seconds to return to the measurement state.

Quick Setup Menu Description

The following is the complete process of the quick setup menu. Please operate in sequence.

1. After the instrument is powered on and stabilized, open the meter cover and press the "E" key to enter the menu group, displaying "GROUP SELECT MEASURING VALUES";
2. Press the "+" key twice until "GROUP SELECT" appears, press the "E" key to enter, and "SETUP COMMISSION QUICK SETUP NO" appears;
3. Use the "+" key, "-" key, and "E" key to enter the password "0050" digit by digit, then press the "E" key to confirm;
4. "SETUP COMMISSION" reappears, press the "+" key to change to "SETUP COMMISSION", press the "E" key to confirm;
5. "LANGVAGE" is displayed, select the language as English, press the "E" key to confirm. If you need to select another language, first use the "+" key and "-" key to select, then press the "E" key to confirm;
6. "PRE-SETTING" is displayed, press the "E" key to confirm, keep the current setting "ACT-SETTJMG";
7. "NIT VOLME FLOW" is displayed, use the "+/-" key and "E" key to change the volume flow unit, finally press the "E" key to confirm;
8. "MEASURING MODE" is displayed, select the current output method, use the "+" key to select "STANDARD" standard type or "SYMMETRY" symmetrical type, usually select "STANDARD" standard type, press the "E" key to confirm;
9. "SEECT OVTPUT" is displayed, select the signal output as current output, or use the "+" key to select "FREQ/PULSE" frequency pulse output, after selecting press the "E" key to confirm;
10. "ASSIGN CURRENT" is displayed, indicating the current output is volume flow, press the "E" key to confirm;
11. "CORRENT SPAN" is displayed, that is, the current output is 4-20mA with HART protocol, press the "E" key to confirm;
12. "VALVE 20mA" is displayed, use the "+/-" key and "E" key to output the volume flow value at full scale, the flow unit must be consistent with the display unit, then press the "E" key to confirm;
13. "TIME ENSTANT" time constant is displayed, usually set to 5 seconds, use the "+" key to set to 5 seconds, use the "E" key to confirm; it can also be changed to other values according to actual conditions;
14. "FAILSAFE MODE" is displayed, that is, the current output during alarm, you can select "MIN CURRENT" alarm current lower limit, "MAX CURRENT" alarm current upper limit (can be set according to actual needs), "HOLD" hold the previous measurement value before alarm, or "ACTURAL" output according to actual measurement value, it is recommended to select "MIN CORRENT" or "MAX CORRENT", press the "E" key to confirm;
15. "SETUP COMPCETE NO" is displayed, press the "E" key to exit;
16. Press the "+" key and "-" key simultaneously and hold for 3 seconds to return to the measurement state;
17. "OPEARATION MODE" is displayed, select the output method as "FREQUENCY" frequency or "PULSE" pulse, can be set as needed;
18. "ASSIGN FREQUENCY" is displayed, indicating the frequency output is volume flow, press the "E" key to confirm;
19. "END VALE FREQ" is displayed, select the full-scale output rate, this value cannot exceed 1000Hz, press the "E" key to confirm;
20. "VALUE Fmax" is displayed, input the full-scale volume flow value, press the "E" key to confirm;
21. "OVTPUT SIGQNAL" is displayed, select the frequency signal as passive positive pulse "PASSLUE—OPSITIVE", or select passive negative pulse "PASSIVE—NEGATIVE", press the "E" key to confirm;
22. "TIME CONSTANT" is displayed, usually the time constant is set to 5 seconds, use the "+" key to confirm, it can also be set according to process requirements;
23. "FAILSAFE MODE" is displayed, that is, no frequency signal output during alarm "FALLBACK VALUE", press the "E" key to confirm;
24. "ASSIGN PULSE" is displayed, indicating the pulse output is volume flow, press the "E" key to confirm;
25. "PULSE VALVE" is displayed, input the pulse equivalent, note that its unit is consistent with the totalizer unit, press the "E" key to confirm;
26. "PULSE UIDTH" is displayed, that is, the pulse width, according to factory setting it is 10.00s, press the "E" key to confirm;
27. "MAX POLSE FREQ" is displayed, that is, the maximum output pulse frequency, can be adjusted as needed, but must not exceed 1250Hz;
28. "OVT PUT SIGNAL" is displayed, that is, the output is passive positive pulse "PASSIVE-POSITIVE", or "PASSIVE-NEGATIVE" passive negative pulse can be selected, usually select passive positive pulse, press the "E" key to confirm;
29. "FAILSAFE MODE" is displayed, that is, the pulse output during alarm follows the factory setting "FAUBACK VALUE" (pulse output is zero during alarm), press the "E" key to confirm.

Key Parameter Setting Reference Table

Following the above steps and parameter recommendations, the setup of the PROMAG50 electromagnetic flowmeter can be completed quickly. During operation, please ensure stable power supply and refer to the manual for detailed configuration.